How much should you invest in house renovations?

How much should you invest in house renovations?

“A broad rule of thumb is that you should spend about 5 to 15 percent of your home value on kitchen renovation,” says Dan DiClerico, a smart-home expert for HomeAdvisor, a home improvement platform in New York City. “So, if your home is worth $300,000, you should spend $15,000 to $45,000 on the kitchen.

How much value does a deck add to a home?

The addition of a wood deck costs an average of $13,333 and the average resale value of it is $10,083. This means homeowners could recoup about 75.6% of the cost once it’s time to sell the home.

Will adding a deck increase my taxes?

Any structural changes to a home or property will increase your tax bill. A deck, a pool, a large shed, or any other permanent fixture added to your home is presumed to increase its value.

How much does a 12×12 deck cost?

Cost To Build A Deck By Size

Deck Size	Square Feet	Average Cost
10×10	100	$1,500 – $3,500
10×12	120	$1,800 – $4,200
12×12	144	$2,160 – $5,040
12×20	240	$3,600 – $8,400

Is it cheaper to pour concrete or build a deck?

Installing a patio flush to the ground can cost much less than a deck. At about $5 a square foot, concrete is usually the least expensive option. Patios are best suited for even ground and the cost of creating a level foundation is very high. Patios don’t require regular maintenance.

What is the least expensive way to build a patio?

Concrete is one of the cheapest and most popular materials that can be used to build a hard-surface patio. The aggregates of concrete can be stone, gravel, sand, or shells, which are mixed with water to form a paste that dries into a hard surface when left to settle.

How much does it cost to put concrete in the backyard?

Concrete Patio Costs The average cost to pour a concrete patio is $2,433, with most homeowners paying between $1,212 and $4,318 for professional installation. Labor costs can run between $3 and $10 per square foot and materials cost $1 to $2 per square foot.

How much does a 10×10 concrete patio cost?

To pour a typical 10×10 concrete slab will cost $670 to $930, a 12×12 slab for a patio will cost $796 to $1,476, a 20×24 driveway slab runs between $1,440 and $3,360, and a 24×24 slab for a garage will cost $3,058 to $5,944. Get free estimates from concrete companies near you.

Can you pour concrete over dirt?

Long story short, yes you can pour concrete over dirt.

Do I need gravel under concrete?

Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.

Can I use pea gravel under concrete?

If you use pea gravel beneath a patio, take a few simple steps to ensure the stability of the base before setting your surface stones, pavers or bricks. Click to see full answer. It should be ok to pour concrete over your gravel walk although you might want to give the concrete a little more depth along the sides.

What type of gravel goes under concrete?

Backfill beneath concrete flat-work along foundation walls should be accomplished with a granular material that is uniform in size. Some fill materials, such as round stones like pea gravel, tend to be self compacting. “I recommend open-graded granular material be used,” says Tull.

What is the best base for concrete?

Most concrete contractors want a mix of coarse and fine aggregate to create a compactable base that is going to be safe for settlement and drainage. Crusher run (a mix of crushed stone and stone dust) is one of the best base materials for concrete flatwork.

Should you put plastic under concrete?

Recently, though, research has shown that the old traditional layer of 6-mil Visqueen (polyethylene plastic) under the slab is seldom effective for two main reasons: Although it may seem water-tight, this grade of material allows a lot of water vapor to pass through.

Is quikrete as strong as regular concrete?

Quikrete fast setting concrete is just as strong as regular concrete. Concrete gets its strength from a chemical reaction that occurs over time during curing. After it’s had time to cure, which usually take 28 days to complete, Quikrete can reach strengths up to 5000 psi.

How long do I need to let quikrete set?

QUIKRETE® Fast-Setting Concrete sets in 20 to 40 minutes. Wait 4 hours before applying heavy loads to the post, such as a basketball backboard. (If the temperature is below 72 degrees, additional time for curing will be required.)