What does reentry code 3 mean on a dd214?
What does reentry code 3 mean on a dd214?
continued Army service
What is SPN code?
Military Separation Program Numbers
What are FMI codes?
Failure Mode Identifier
What does FMI 4 mean?
FMI: 4. Lamp: AMBER. SRT: REASON: Sensor Supply 1 Circuit – Voltage Below Normal or Shorted to Low Source. Low voltage detected at sensor supply number 1 circuit.
What does FMI 31 mean?
SPN 521049/FMI 31 Description This Code Sets When There is a Code Present for the Diesel Exhaust Fluid (DEF) Tank Level, DEF Dosing Unit, DEF Pump, NOx Sensors, Blocked DEF Line, DEF Quality, NOx Efficiency, Selective Catalyst Reduction (SCR) Harness and/or SCR Sensor.
What does voltage above normal mean?
shorted to high means voltage is reading higher than normal which could be caused by a faulty sensor or a short in the harness from another power source. 1678 Catalyst Tank Temperature – Voltage Above Normal, or Shorted to High Source.
What does FMI 16 mean?
FMI: 0/16. Lamp: AMBER. SRT: REASON: Crankcase Pressure – Data Valid but Above Normal Operational Range – Moderately Severe Level.
What is SPN FMI?
Suspect Parameter Number (SPN) Represents the SPN with error. Every defined SPN can be used in a DTC. Failure Mode Identifier (FMI) Represents the nature and type of error that occurred, e.g., value range violation (high or low), sensor short-circuits, incorrect update rate, calibration error.
What does shorted high mean?
the maximum acceptable voltage level
What is a J1939 code?
J1939 is a set of standards that defines how information is transferred within a CAN to communicate information between ECUs. While a CAN provides a tool for communication, J1939 is a higher-layer protocol that provides a language for communicating using that tool.
How do you clear fault codes on Cummins?
How to clear fault codes on Cummins Insite Pro: After you connect to the ECM with Insite, click the “Fault Codes” tab on the left. After the codes are displayed, highlight one of them & right-click on it. Select “Erase all Faults” and follow the instructions.
How do you clear the fault code on a ISX Cummins?
Cycle the key switch to the ON position for 30 seconds, then cycle the key switch to the OFF position for 30 seconds. Start the engine and let it idle for 1 minute. The fault code status displayed will change to INACTIVE immediately after the diagnostic runs and passes.
How do you clear an Onan fault code?
How to Clear a Fault Code on Onan Generator
- Locate the primer button on the generator. It is located on the side of the unit, below the gas tank.
- Hold the primer button down for at least 30 seconds.
- Release the button and start the generator.
- Allow the generator to run for 15 minutes, to ensure that the code has cleared.
How do I prime my Onan 4000 generator?
They don’t have a prime button: You hold down stop for 20-30 seconds (the light will light up indicating that the fuel pump is running).
Does an Onan 4000 Generator have an oil filter?
Looks like you have a MicroQuiet 4000 generator. They are a small single cylinder engine and it does not have an oil filter.
What oil should I use in my Onan 4000 generator?
Onan RV recommends changing the oil every 100 hours or once a year, whichever comes first. It only takes about 20 minutes and you will be good to go for the season. You will need a T30 torx bit, a 12mm socket, an oil pan, a funnel and 1.6 quarts of SAE30 or 15W-40 oil.
How do you prime a generator?
How to Prime Fuel to My RV Generator
- Check the level in the fuel tank.
- Check the inline fuse.
- Locate the prime button, which actuates a prime relay.
- Depress the momentary push switch if your generator does not have a prime button.
Can you jump start a generator?
you can jump start the generator using auto style jumper cables. just connect them to where the incoming cables from battery connect to the generator. once started you will have to leave them attached until the generator actually starts to output 120vac power and the transfer switch connects to the generator.
Can you jump start a generator with a car battery?
How does one go about jump starting a generator with a dead 12V battery using jumper cables and a vehicle? The exact same way you would jump start another car with a dead battery. Run the engine; connect like battery terminals, wait a little while and start the generator.
What causes the generator not to start?
If there is no spark, this indicates that the spark plug is defective and should be replaced. The carburetor might be clogged. A clogged carburetor is most commonly caused by leaving fuel in the generator for a long period of time. This sticky fuel can clog up the carburetor and prevent the engine from starting.
